Flat plate through-type engraving die

The pattern and shape of the die-cutting mold can be customized freely. It is made of imported steel with high hardness. It can be formed in one cut and has no joint cutting edge. High-precision high and low die-cutting molds can be made on the same steel plate. The blade can be retrimmed, meaning that after the blade becomes blunt, it can be retrimmed and become a new blade. It can be designed with different process holes, steps, indentations, positioning, and blade heights, providing unlimited possibilities for special die-cutting requirements. The products die-cut have smooth cut surfaces without seams and a long die-cutting life.

Automatic waste removal type engraving knife molds

During the die-cutting process, the waste at the middle hole of the product can be quickly squeezed towards the waste removal trough at the bottom of the die, and then the waste can be removed by suction or blowing, ensuring the smooth progress of the die-cutting process and the quality of the product. The production of the bottom automatic waste removal type engraving die requires two more processes than that of the ordinary engraving die (wire cutting processing of the waste removal hole and processing of the back waste discharge trough).

Pre-pressed elastic ejection type engraving die

It is applied in the automotive industry, medical and health industry, label industry, electronics industry, packaging and printing industry, LED industry, etc

Automatic waste removal type engraving knife molds

The waste suction type engraving die is based on the bottom automatic waste removal type engraving die and adds a suction device. It can quickly suck away the waste in the die-cutting products through the suction holes on the side. Compared with the bottom automatic waste removal type engraving die, this type of engraving die has a higher waste removal efficiency

Metal composite engraving die

The metal composite engraving die is suitable for die-cutting harder and thicker materials, and the product has the feature of fully piercing through the waste part and half piercing through the finished part. Products with this feature need to be die-cut in several stages in the processing of other molds, and the effect is difficult to guarantee. The metal composite engraving die successfully ensures the quality of die-cutting and greatly improves the processing efficiency. In addition, the grooving method is slow wire cutting. The metal composite type engraving die is composed of two major parts (the engraving die with precise nesting design and the metal punch die with protective shoulder design).

Mirror etching mold

The mold has no cutting edge, and the precision of the die-cutting mold is high. During the die-cutting process, the product size is stable. The maintenance requirements for the mold during storage are simple, and long-term storage will not affect the product size. The blade Angle and height can be designed according to the processing technology requirements of the product. The flat height of the mold can be applied to the installation in QDC molds and various hardware mold frames.

Electronic film etching knife mold

It is used for punching and cutting protective films for some precise small accessories inside electronic products. Products like punching and cutting have extremely high precision requirements. Due to the special nature of the material itself, the requirements for this type of product are also very high. For this type of product, the die needs to be designed according to the characteristics of the material. In addition to achieving a precision of 0.03 to 0.05mm, there are also high standards for the flatness of the entire die and the smoothness of the punching and cutting

Special blade etching mold

It mainly refers to lens treatment, polishing processing or Teflon treatment, etc. This type of die-cutting die is mainly applied to: materials with high requirements for the side processing of customer products, smooth cutting edges, materials that are prone to re-adhesion, products that are difficult to remove waste, and products combined with some special processes

Single-sided knife etching mold

For die-cutting products with small spacing, thick materials, prone to indentation, and high quality requirements, the blade of such molds has one side as a straight edge. Generally, the side of the product is a straight edge. The mold-making process will take a relatively long time. The production cycle is generally over 24 hours, and in special circumstances, it may take even longer. The maximum spacing of the molds can be as small as 0.5MM

Laser die-cutting mold rubber sheet mold

The rubber sheet mold is made by laser cutting PVC rubber sheets and installing blades in them. The gaps cut out are uniform. The material is relatively soft and prone to loosening. If the product does not require high precision, the rubber sheet mold can be used. Rubber sheet molds have a relatively low cost and can meet the die-cutting requirements of various electronic materials, bringing revolutionary changes to the die-cutting problems of electronic materials and effectively solving the large errors caused by the traditional manual production process through sawing machines.

Laser knife mold wood board mold

It is applicable to FPC products, backlight products, conductive shielding products, buffer sealing foam products, protective film products, labels, nameplates, dust-proof products, adhesive fixation products, graphite sheet products, insulating conductive products, etc

Sandwich composite knife mold

The sandwich composite interlayer mold mainly has inconsistent material selection. It is composed of single or multiple layers of boards and fastened with screws. When in use, it will not loosen due to the vibration of the die-cutting machine during operation and has good stability. It can be inlaid with engraved holes and automatically clear waste holes. It can be cut or pressed into various shapes of flat products, flat products with concave-convex patterns and/or indentation lines, and is widely used in packaging and printing, electronics, vacuum forming and other industries.

Aluminum plate/steel plate/iron plate for knife mounting

The blades used for iron/steel/aluminum plate molds are the same, but the main difference lies in the material. They are processed by wire cutting, resulting in uniform gaps and high precision. As they are made of metal, they have high hardness and good stability, making it convenient to replace the blades. At the same time, they can be inlaid with engraved holes and automatic waste removal holes. They are generally used for products prone to mold explosion.

QDC hardware mold

Mainly, the combination of metal molds with etching molds or engraving molds can achieve the process of removing small hole waste and die-cutting the product shape in one go during the processing of die-cutting products. The waste inside the product is completely sealed and the shape is die-cut. The production and processing are stable, the mold life is long, and it can process some products with thick materials and high hardness. The mold can be repeatedly repaired. It has a good die-cutting effect on small hole nesting.

Nesting QDC mold

The nesting QDC die is a QDC die used on the small hole nesting die-cutting machine. (To design this type of die, one must first understand the stroke and clamping method of the small hole nesting machine, then combine the function of the small hole nesting, and also understand the process of the customer's die-cutting products, and then design the structure of the die to maximize the value of the die.) It is suitable for: The small hole socket die-cutting machine is stable during production and processing, has a long service life, can be repeatedly maintained, and has a good die-cutting effect.